Get Control Inc E84 Serial to Panel Controller KLA01102 REV 2 & interface (4162)

• Manufacturer: Get Control Inc
• Part #: KLA01101 Rev 2 
• Model: E84

• Get Control Inc P/N KLA01102 REV 2 E84 Controller 
• Light Curtain Mix DAFP P/N 313-000-901 REV 1 Light Curtain Emitter Receiver

• The GCI E84 Serial to Parallel Controller (E84 SPC) is an off-the-shelf solution used by 300mm equipment manufacturers to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection. All handshaking functions are performed automatically with error detection and reporting, requiring only a minimal amount of communications overhead with the equipment controller. Alternatively, the E84 SPC can be implemented as a stand-alone controller utilizing its placement and presence sensor inputs. The E84 SPC is mounted in an extruded aluminum enclosure. The E84 SPC can optionally be ordered without the enclosure for mounting into standard three inch Snap Track. An AMP 3mm Micro MATE-N-LOK connector is provided for all external wiring, including the RS232 interface (transmit, receive, and ground), three auxiliary inputs (for use with load port placement and presence sensors), one auxiliary output, and system power. A female DB-25 connector provides a fully compliant passive E84 PI/O interface to connect with the factory AMHS or optical transceiver device. It provides 16 optically-isolated E84 I/O signals plus three reserved optical transceiver signals: Select, Mode, and Go. LEDs are provided to indicate the state of each PI/O interface signal. The +24V signal is available to power an optical transceiver device. An API consisting of a line-based ASCII message set provides the software interface to the host controller. The API provides an automatic mode of operation to perform the E84 Load and Unload handshakes with minimal host intervention. Manual mode allows the host controller to control and monitor individual PI/O signals. The E84 SPC requires a single +18 to 30 VDC 200 mA power source.
• An additional user interface is included
• Sells for $1,495 New from Manufacturer 

Sold as is with 30 day Right of Return, only pictured items included
Easy return/refund for any reason
Anacapa Equipment

RETURNS 
Anacapa Equipment Brokers, Inc. (“Seller”) strives to offer excellent customer service.   You may return any equipment purchased from us for any reason within thirty (30) days after your receipt of the equipment for a full refund of the purchase price, provided that returned items are received in the same condition as sent.  We DO NOT ship internationally.  If you are using a freight forwarder then returns are VOID.  
SHIPPING                                                                                                               All equipment purchased is shipped within one (1) business day (subject to freight availability) after receipt of payment and is shipped FOB place of shipment.  We only charge actual shipping cost.  If eBay overcharges for shipping, we issue an immediate refund for the difference. If you are undercharged, we will absorb the cost. We DO NOT ship internationally.  IF you are using a freight forwarder then returns are VOID.   
LIMITED WARRANTY                                                                 
Buyer acknowledges that the equipment is being sold “as is" and without any warranty of merchantability or fitness for a particular use.  The entire risk as to the quality and performance of the equipment is with the Buyer.  Should the equipment prove defective following its purchase the Buyer and not the Seller, manufacturer, distributor, or retailer assumes the entire cost of all necessary servicing or repair.  Buyer may inspect the equipment prior to purchase and placement of the order.  Failure to inspect prior to placement of an order is deemed a waiver of Buyer’s right to inspect.  Buyer is responsible for determining the suitability of the equipment for its application.  Seller assumes no liability for the use or misuse of any equipment purchased by Buyer. It is assumed that the equipment will be installed and operated by qualified personnel. The Buyer agrees that the Seller shall not be held responsible or liable for any injuries or damages, whether incidental or consequential, associated in any way with the equipment purchased.  The Buyer, by purchasing this equipment, indicates its acknowledgment of, and agreement, to the terms of this limited warranty. 
INDEMNITY                                                                                                            
Buyer shall be solely liable for, and shall defend, indemnify, and hold Seller, its Affiliates, and all of their respective directors, officers, employees, agents, and independent contractors (“Indemnitees”) harmless from and against any and all damages, liabilities, injuries, losses, costs (including reasonable attorneys and experts fees at trial and on appeal), and expenses which may be incurred by, asserted against, or recoverable from any Indemnitee as a result of any actual or threatened action, suit or proceeding arising out of or relating in any way to the purchase of equipment from Seller.  The validity and interpretation of this Agreement and the enforcement thereof shall be governed by the laws of the State of California without regard to any principles governing conflicts of laws.  Any dispute arising from the purchase of equipment from Seller must be resolved in the State Courts of California.