ElectroDamp Vibration Isolation Table System Ametek TMC HAWK Insight EDII 9421

Manufacturer: Ametek | TMC
Model: HAWK Insight EDII (ElectroDampII) System
Date of Shipment New: 04/04/2014

Includes:
Insight EDII System TMC Table: 24-35425-01
Power Transformer Model: 22-33171-01
Linear Power Amplifier, LPA-70 Model: 22-29474-01
DC-2000 Controller, Insight Model: 22-35420-01
DC-2000 Precision Valve Box Model: 20-27955-01
CD: Controller Software PN: 95-34577-04, Setup & Operation Manual PN: 96-29581-01
Spare Air Tubing

Specifications: (These specifications were taken from an online user manual and may not be accurate to this product.)

General
Settling time: 0.2 s **
Active degrees of freedom: 6
Height control accuracy: < 10 µm at sensors

Linear Actuators (horizontal & vertical)
DC resistance: 5 O
Force constant: up to 12 lb./A | 55 N/A
Max. continuous force: 25 lbs. | 110 N
Peak force @ 7 A: 87 lbs. | 385 N
Electrical time const.: 2.6 ms
Stroke: 0.25 in. | 6.4 mm
Transverse clearance: 0.09 in. | 2.3 mm
Stray field: < 1 G @ 2 in.
Dimensions (WxDxH): 2.8 x 6.8 x 4.5 in.

Valving (active only)
Valve type: Proportional E/V servo
Control type: Pressure or air flow
Max. flow rate: 1.5 SCFM
Air consumption (4 isolators): < 2 SCFM (no stage motion)
- 3 dB response: = 10 Hz typ.

Height Control Sensors
Type: Non-contacting inductive (eddy current)
Electronic configuration: Two-wire NAMUR; Three-wire 30 or 18 mm dia.
Range: 15 mm nominal for 30 mm wire; 6 mm nominal for 18 mm wire
Resolution: < 1 µm

Passive Pneumatic Mount
Standard capacities: 1,000, 2,500, 3,300, 5,700 lbs. @ 80 PSI
Damping (10:1): < 3 s

DC-2020 Digital Controller
Processor: Dual core: DSP @ 150 MHz & Cortex M3 @ 75 MHz
Analog I/O: 32/24 channels (16/16 bit)
Sampling rate: 5 kHz nominal
Front panel: Power switch, 3-color status LED, Ethernet RJ-45, MicroSD card slot, 2x BNC sockets (each can be input or output), 2x USB 2.0 ports (Type B and Micro B), FW upgrade button
Rear panel: Power entry, Analog I/O sockets, Pneumatic ports, Ethernet RJ-45, 1x USB 2.0, RS-232 DB 9, Relay socket
User interface: GUI via USB or ethernet
Power: 90-240 VAC, 50-60 Hz, 100 W max.
Dimensions (WxDxH): 16.8 x 9.0 x 1.75 in.

Power Amplifier
Channels: 8
Max. current per channel: 7 A
Type: Linear
Peak power: 700 W total
Cooling: Ambient, forced air
Protection: Resettable fuses, electronic thermal, over current, under voltage
Operation: Remote or manual
Dimensions: 1 RETMA rack unit height x 15 in. (381 mm) depth

Dimensions

Actual Dimensions: 45 3/4 x 56 x 35"
Shipping Dimensions: 77 x 59 x 48"
Shipping Weight: 2160 lbs

Crating Fee: Ask for a Quote
Sold as is with 30 day Right of Return, only pictured items included
Easy return/refund for any reason
Anacapa Equipment

RETURNS 
Anacapa Equipment Brokers, Inc. (“Seller”) strives to offer excellent customer service.   You may return any equipment purchased from us for any reason within thirty (30) days after your receipt of the equipment for a full refund of the purchase price, provided that returned items are received in the same condition as sent.  We DO NOT ship internationally.  If you are using a freight forwarder then returns are VOID.  
SHIPPING                                                                                                               All equipment purchased is shipped within one (1) business day (subject to freight availability) after receipt of payment and is shipped FOB place of shipment.  We only charge actual shipping cost.  If eBay overcharges for shipping, we issue an immediate refund for the difference. If you are undercharged, we will absorb the cost. We DO NOT ship internationally.  IF you are using a freight forwarder then returns are VOID.  
LIMITED WARRANTY                                                                 
Buyer acknowledges that the equipment is being sold “as is" and without any warranty of merchantability or fitness for a particular use.  The entire risk as to the quality and performance of the equipment is with the Buyer.  Should the equipment prove defective following its purchase the Buyer and not the Seller, manufacturer, distributor, or retailer assumes the entire cost of all necessary servicing or repair.  Buyer may inspect the equipment prior to purchase and placement of the order.  Failure to inspect prior to placement of an order is deemed a waiver of Buyer’s right to inspect.  Buyer is responsible for determining the suitability of the equipment for its application.  Seller assumes no liability for the use or misuse of any equipment purchased by Buyer. It is assumed that the equipment will be installed and operated by qualified personnel. The Buyer agrees that the Seller shall not be held responsible or liable for any injuries or damages, whether incidental or consequential, associated in any way with the equipment purchased.  The Buyer, by purchasing this equipment, indicates its acknowledgment of, and agreement, to the terms of this limited warranty.
INDEMNITY                                                                                                            
Buyer shall be solely liable for, and shall defend, indemnify, and hold Seller, its Affiliates, and all of their respective directors, officers, employees, agents, and independent contractors (“Indemnitees”) harmless from and against any and all damages, liabilities, injuries, losses, costs (including reasonable attorneys and experts fees at trial and on appeal), and expenses which may be incurred by, asserted against, or recoverable from any Indemnitee as a result of any actual or threatened action, suit or proceeding arising out of or relating in any way to the purchase of equipment from Seller.  The validity and interpretation of this Agreement and the enforcement thereof shall be governed by the laws of the State of California without regard to any principles governing conflicts of laws.  Any dispute arising from the purchase of equipment from Seller must be resolved in the State Courts of California.